While your hot tub is in sleep mode (or ‘SL’ & SLP mode on some models), the jets will operate occasionally to filter the water. In sleep mode, your hot tub’s heater will usually only kick on once the temperature dips below 20 degrees of the set temperature.
What does SLP mean on Balboa hot tub?
Balboa topside displaying SL or SLP. If the “SLP” or “SL” Message is Alternating with the Water Temperature on the Topside Display, the Spa is Operating in the “Sleep Heating Mode“. This is NOT an error message. Note that a Sleep Heating Mode will drop the water temperature 20 degrees below the set temperature.
What mode should my hot tub be in?
Economy is a good setting for those who use the hot tub daily. The drop in temperature fluctuates during the year from minor or no temperature falls in the summer, to larger drops in the coldest part of winter.
What are the codes on a hot tub?
CODEERROR CODE DESCRIPTIONCE 04Water sensor/pressure switch faultCE 05Temperature sensor, or water is dangerously hotCE 06High limit manual reset on heater is trippedCE 07Stuck heater relayWhy is my hot tub flashing SL?
If the SLP or SL Message is Alternating with the Water Temperature on the Display, the Spa is Operating in the Sleep Heating Mode.
How do you adjust the heat on a Balboa hot tub?
On panels with “Warm” and “Cool” buttons, to display the set temperature, press “Warm” or “Cool” once. To change the set temperature, press a temperature button again before the display stops flashing. Each press of “Warm” or “Cool” will adjust the set temperature.
What does F2 on a hot tub mean?
The F2 error code is usually from a balboa power pack system and normally is referring to a flow issue in your hot tub. … A dirty filter can often be the culprit here so make sure to either replace or give your hot tub filter a good cleaning. Look at your intakes and out takes and make sure they are clear of debris.
Why are my hot tub jets not working?
Jets Are Not Working Properly When jets start failing, the most likely case is that your hot tub pump is not working correctly. … Clogged filters or water intakes can also cause jet issues. Clean them to enhance water flow. If you cannot clean the filter properly, you may need to replace.What does HR mean on hot tub?
If you are seeing an HR code on your hot tub it means there is a hardware error on the motherboard that is not repairable. Try to reset the breaker but if that doesn’t work the pack will need to be replaced.
What is SE on hot tub?SE = Spa operating in Standard-in-Economy Mode.
Article first time published onWhat temperature should you keep your hot tub when not in use?
While it may sound like common sense to turn your hot tub down every time it is not in use, it’s actually better to maintain a constant soaking temperature, which is typically around 100° Fahrenheit for many people.
Should I leave my hot tub on all the time?
One question we sometimes get asked is should I leave my hot tub on all the time? The answer is yes! Hot tubs are designed to be left on permanently and this is how they work best. Of course, they’ll need to be drained regularly but for the most part, they are left on 24/7.
What does F8 mean on a hot tub?
Filtration Cycles run from F1 to F8 (F1 = 1 hour every 12 hours / F8 = 8 hours every 12 hours). Preset cycle set from factory is F1, so if in ec or sl mode your water will not reach desired temperature.
What does f1 mean on my hot tub?
FL1 hot tub code – indicates that there is an error with the flow switch and it is stuck in the open position.
What does test GFCI mean on a hot tub?
A Ground Fault Interrupter (GFCI) Trip Test must occur to allow proper spa function. … If a GFCI does not trip properly, your spa’s display will show an error message. GFCI breakers are important safety devices required by code for your hot tub.
What does SL mean on clever spa?
A SL Error Code showing on your CleverSpa® Control Panel can mean there is a blockage in the system which is preventing hot water from circulating. We can offer guidance to help resolve the problem.
What does PR mean on Beachcomber hot tub?
MessageMeaningPrThis happens when the hot tub unit is actuated for the first time; eventually it goes into priming mode–F / –CMeans unknown St STANDARDMeans hot tub unit is functioning in Standard Ec ECONOMYMeans hot tub unit is functioning in Economy mode.
What does F3 mean on a hot tub?
Filter Cycles The filter program also controls how the spa heater operates as follows: • Standard filter programs (F0, F1, F2, F3): Heater activates anytime water temperature drops 2 degrees below the set temperature (Jets 1 low speed also activates on non-Circulation Pump models).
Where is the high limit reset button?
The High Limit Reset Button is located behind the gas valve.
What is Watchdog call for service?
A: This means your spa has deactivated itself and is in watchdog mode. It has disabled itself to prevent further damage. Sometimes, it is just a little power spike and can be fixed by turning the breaker off for 10 seconds and back on. If this doesn’t do it, first check for proper voltage.
Why does my hot tub keep switching off?
First, check your water level. Then, look for clogs in your circulation system, and wash or change your filter. … If the high limit switch shut your heater off because your water got too hot or you have air trapped in your lines, resetting the heater will get it going again.
What does SL mean on Balboa hot tub?
If the SLP or SL Message is ON Solid (Not Flashing) on the Display, the Spa is Operating in the Sleep Heating Mode, but there is No current water temperature because the Spa is between Filter Cycles.
What is rest mode Balboa?
Rest Mode. When in Rest mode, the spa will not heat unless the filtration cycles are in operation. If the spa is displaying “RUN PUMP FOR TEMP”, it is likely in Rest mode and the spa has not circulated for over 1 hour.
What is hot tub polling?
In Ready mode, your spa will perform ‘polling’. This means your jets will run on low speed for a 5-minute interval every 30 minutes to circulate the water and check its temperature. If the temperature is detected to be lower than your set temperature, your spa’s heater will power on to bring the temperature up.
Where is the temperature sensor on my hot tub?
On most hot tubs, this sensor is located just inside of the filter housing. The temperature probe should be pushed down securely into the thermowell, and the capillary should not have any kinks.
How do you test a hot tub temperature sensor?
- Shut off all power to the spa at the breaker and spa pack.
- Set your Ohm meter to the 20K setting.
- Locate the wire ends and remove the plug from the board.
- Place your meter leads onto the green and red wire.
- Compare readings to Thermistor Resistance vs. Temperature Chart.
How do I reset my Gecko spa?
Loosen the two screws that hold the cover onto the control pack. Lift the cover off to reveal the LED board. Check the LED board to see if there are three flashing dots on it. Turn the circuit breaker off if so, then back on to reset the system.
Why won't my bathtub jets turn on?
If your home has experienced a recent power surge or power outage, you may need to head to the breaker box and check to see if the control for your jetted tub is turned to the “off” position. If so, simply turn it back to the “on” position. … The fix may be as simple as cleaning or replacing the tub’s filters.
What does Fl mean on a hot tub display?
Today’s post is about water flow trouble codes on your spa panel. These are usually presented as FL, FLO or FLOW on your display, although it may appear as LF (Low Flow) or PS (Pressure Switch). Low flow error codes are really a self-preservation exercise for your hot tub.
What is a good temperature for a hot tub in the summer?
Setting Hot Tub Water Temperature in the Summer As a rule of thumb, many users keep their hot tub set at temperatures ranging between 97-99 degrees.
How often should I drain my hot tub?
Draining and refilling your spa will be an important aspect of spa ownership. Many spas need to be drained and refilled every three to four months due to chemical build-up.
