What does f9 mean on a whirlpool range

F9 – Oven Door Lock Failure – Check door lock switches and wiring. Check for stuck lock switch.

How do I fix the F9 on my Whirlpool oven?

Power unit down by turning off the circuit breaker(s) for one (1) minute.
Monitor the range or oven for one (1) minute to ensure the error code does not display again.
Verify the range or oven operation.

What does the code F9 mean on a Whirlpool electric stove?

This code will most often indicate that the appliance is wired incorrectly at the home electrical supply, or at the hard wire connection. … If your oven was installed recently (within approximately 3 months), contact a qualified electrician to verify the electrical supply.

How do I fix error code F9?

Reset the Oven Sometimes, the F9 error code is the result of an electrical fault that has magnetized the circuitry. Resetting the oven by disconnecting the power for five minutes will demagnetize the circuitry and resolve the F9 error.

How do you clear the error code on a Whirlpool oven?

Plug the oven power cord back in or turn ON circuit breaker. Press CANCEL on the display. If fault code comes back after 1 minute then replace the keypad. If F2 E0 persists then replace the electronic oven control.

How do I clear F9 code?

Hold on the “Start/Stop” button for 10 seconds. This will end the beeping. Unplug the oven for 30 seconds and plug it back in to clear the flashing error code from the screen. If you try to operate your oven again, the error code will appear so do not use any of the oven’s functions.

How do I clear E1 F9 code?

Try a Reset. Sometimes an error code is caused by a control board glitch, where resetting the washer is all it takes to resolve the error code. …
Check your Detergent. …
Check the Drain Hose. …
Clean the Filter. …
Check the Drain Pump. …
Check the Wiring.

How do I fix error code F9 GE oven?

Reset. When an error code appears on the GE oven display, resetting the appliance can resolve the problem. Disconnect power to the oven for 30 seconds before plugging the oven back in. If the oven is built into an electrical system, shut off the circuit breaker and then wait 30 seconds to reset it.

How do you clear the code on a whirlpool F9?

F9 – Oven Door Lock Failure – Check door lock switches and wiring. Check for stuck lock switch. FH – Detects No Water Entering Machine or No Pressure Switch Trip – Select ‘cancel’ twice to clear this code.

What is F9 in AC?

F9: This error code shows up only when there is an issue with the outdoor DC fan. P2: This error code shows up only when there is an issue with the Compressor phase current protection. P3: This error code shows up only when there is an issue with the outdoor unit AC voltage protection.

Article first time published on

Why is my Whirlpool oven not heating up?

Defective Whirlpool Oven Bake Element An electric oven not heating up can often be attributed to a defective bake element. … If the bake element is defective, you may notice burnt spots or even breakage on the metal coil. In these instances, the bake element is defective and should be replaced.

How do I put my Whirlpool oven in diagnostic mode?

Enter Diagnostics mode by pressing CANCEL>CANCEL>START within a 5-second period. Entering Diagnostics mode will cancel any active oven operation. Enter the Diagnostics mode only after the oven is cool. All elements (depending on which cycle is being used) will operate with the oven door open.

How do I stop my Whirlpool stove from beeping?

A Whirlpool oven can keep beeping because of a faulty temperature gauge, control panel or keypad. Continuous beeping from your Whirlpool oven could indicate a problem. Sometimes you can resolve it by simple pressing the cancel button and resetting the oven.

Is there a reset button on a Whirlpool oven?

Press the “Off/Clear’ button for three seconds to turn the “Control Locked” child lock off. Reset the cooking program if “Off/Clear” was pressed accidentally. For example, press the “Defrost” button again, and turn the dial to select the defrost time you want again. Press “Start.”

How do I read a whirlpool error code?

Error CodeErrorrL or F34Items were detected in the washer during the Clean Washer cycle.Sud or SdThere are too many suds in the washing machine.F5 E2The door is not locking properly.F7 E1Indicates a motor speed sensing error,

What does code PF mean on Whirlpool oven?

Whirlpool PF – Power failure (not a failure mode) The manufacturer has assigned this error or fault code to indicate that the appliance lost power temporarily.

Why is my Whirlpool washer saying E1 F9?

If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. … Remove any clogs from drain hose.

How do you clear the error code on a Whirlpool top load washer?

System error code. Press START/PAUSE once to clear the code, then press START/PAUSE again to restart washer. If the code doesn’t clear, Contact Us or Schedule Service Online. Hot and cold inlet hoses have been installed incorrectly (reversed).

How do I fix E1 error on my Whirlpool washer?

Check that the water faucets are not closed.
Check that the water pressure in the house is over 20 kPa.
Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement.
Check that the drain hose is not below 27½” (700 mm) from the floor.

Why does my oven say locked?

You may find your oven has arbitrarily locked itself when you weren’t even using it. If you try to use your oven and find it locked, press the “clear” or “reset” button to stop the oven and turn it off. Wait a minute or two and then try to open it again. If it’s still locked, start an oven cleaning cycle.

Why does stove say f9e0?

New installation or electrical connection? … This code will most often indicate that the appliance is wired incorrectly at the home electrical supply or the hardwire connection. If your range was installed recently and is not functioning, contact a qualified electrician to verify the electrical supply.

What does F9 mean on Frigidaire oven?

On Frigidaire stoves, an error code with F9 means that the door on the stove isn’t closing properly. This code may come up when something is clogging the latch, the door latch is broken or the switch assembly needs to be replaced. Some owners have found that this error code shows up after they run a self-clean cycle.

What does F9 mean on Maytag oven?

The F9 error code indicates a problem with the oven door lock assembly. The door lock assembly will need to be checked and replaced if defective. If the door lock assembly is okay, then the electronic oven control board will need to be replaced.

How do I fix F1 error in AC?

Find the reset button in the lower right corner of the air conditioner remote control. Open a paperclip or something similar and hit the reset button with it. Wait for the device to reset. Follow the AC power cord from the air conditioner to the outlet.

How do I resolve P3 error in Lloyd AC?

P3: This error code usually shows up when there is a lack of gas in the system. The solution to this issue is to fill up the gas or call up the service center.

How can remove h1 error in AC stabilizer?

Plug out the stabilizer from mains board and Check the input / incoming voltage in the mains socket using a multimeter. If it is in the range in between 180 to 240 volt then its okk . Now bypass the stabilizer and connect AC directly to the mains supply only for serviceability check, hope it will work.

How do I know if my oven temperature sensor is bad?

Longer Than Usual Cooking Times. …
Undercooked Foods. …
Uneven Cook on Your Meals. …
Overheating Issue. …
Solving the Problem With a Troubleshooting Tip. …
Trying out an Ohmmeter. …
Discovering a Combination of Problems. …
The Oven-Board Failure.

How do I fix my oven that is not heating?

Check the temperature sensor. …
Use an ohmmeter to make sure the sensor is functional. …
If the sensor isn’t working, replace it.
Verify that the heating element or gas igniter is working, and replace it if not.
If everything’s been checked or replaced, recalibrate the oven.

What are the symbols on an electric oven?

Fan oven symbol. The standard setting for many electric fan-assisted ovens shows a fan, often inside a circle. …
CircoTherm® symbol. …
Circo-roasting/grill with fan symbol. …
Bottom heat symbol. …
Top and bottom heat symbol. …
Pizza symbol (fan with bottom heat) …
Bread baking symbol. …
Slow cooking symbol.

What does E2 F3 mean on a Whirlpool oven?

An E0-F3 error indicates that the oven’s temperature sensor is open; E1-F3, that the temperature sensor is shorted; E2-F3, that the oven temperature has exceeded the maximum rated 575 degrees Fahrenheit in “Cook” mode; and E3-F3, that the oven temperature has exceeded the maximum rated 950 degrees Fahrenheit in “Clean” …

What does CLR mean on Whirlpool oven?

You don’t mention any other problems or if you can select and change cycles but “CLR” is short for “Clear” and would indicate a problem with the over control. Check if the control lock is turned on by pressing and holding the “Start” keypad for 3 seconds and see if the “Loc” light goes out or comes on.