How much does it cost to rebuild a 4l60 transmission

This item 4L60E Transmission Rebuild Kit Heavy Duty Master Kit with 3-4 Power-pack4L60E 4L65E 4L60-E Master Overhaul Rebuild Kit With All Alto HEG Heavy Duty FrictionsPrice$28500$255.00$255.00Sold ByWorld Wide Parts OutletWorld Wide Parts Outlet

How much is it to rebuild a 4L60E?

Can you rebuild a 4L60E transmission?

At a glance, the 4L60 doesn’t look much different than a 700-R4. … Unless you are a seasoned transmission builder with a lot of experience with the 4L60E series transmissions, it is suggested you never execute transmission rebuilding yourself.

How long does it take to rebuild 4L60E?

Someone has to know the exact condition of your car to answer this question. The estimated time is about 8 hours. To rebuild the transmission is an additional 6 hours.

What does a 4L60E transmission cost?

TransmissionStreet Smart TransmissionAutozone4L60E / 4L65E16711699

Is it hard to rebuild a transmission?

Difficulty Level Rebuilding an automatic transmission is generally regarded as a difficult undertaking because the repair shop must be familiar with your specific type of transmission. Automatic transmissions vary widely from one vehicle to the next and each requires totally different parts and tools to rebuild.

Is it worth it to rebuild a transmission?

Rebuilding a transmission can save you a lot of money over the short-term, while keeping car payments out of your monthly budget. For many, rebuilding their transmission is worth the initial cost. Rebuilding a transmission may cost you twenty-five hundred dollars or more, which is a significant chunk of change.

What causes a 4L60E transmission not to shift?

The 1-2 shift failure on the 4L60E is often due to a faulty throttle position sensor (TPS). … A more serious cause of 1-2 shift failure on the 4L60E is a leak in the 2nd gear apply circuit (servo assembly or 1-2 accumulator). You can test for this by using an external pressure gauge.

How long do 4L60E transmissions last?

4l60e from 1996 held up well. Reverse kinda was finicky, every now and than it would slip but had a good life. I honestly think around 250-300k it should be rebuilt if its original.

Will a 4L80E replace a 4L60E?

The 4L80E has been used in a number of 1/2-, 3/4-, and 1-ton GM trucks over the years. Upgrading from the 4L60E to the 4L80E is akin to going from a Dana 44 axle to a Dana 60–you’ll add some weight, but also add durability.

Article first time published on

What years was the 4L60E used?

4L60E/4L65EOverviewProduction1992–2013Body and chassisClass4-speed longitudinal automatic transmission

Is a 4L60 the same as a 4L60E?

The 4L60 designation, while the same for the 4L60 and 4L60E represents the fact the transmissions are four gears, Longitudinally positioned, The engine is capable of supporting a 6,000-lb Gross Vehicle Weight Rating (GVWR).

How long does it take to rebuild a transmission?

So how long does it take to rebuild a transmission? Most people need their cars running again as soon as possible. This can depend though, it can be done in as little as one day although the average is usually between three to four days.

How much are transmission rebuild parts?

A rebuild may cost you between $2800 and $3800 depending on labor, parts and unforeseen circumstances. This is still relatively cheaper than a new transmission, which could cost between $4000 and $8000 depending on the make and model of your vehicle.

Why is my 4L60E transmission slipping?

Slippage can occur due to several possible causes, such as low fluid level, a slipping torque converter clutch, or slipping clutch or band within the transmission. … The clutch locks the engine and transmission together, overriding the fluid coupling. GM valve body wear has become an issue for two reasons.

Can you fix a transmission without replacing it?

Transmission Repairs Often with a transmission repair, you are only fixing one specific part of the transmission. This repair can take place without having to rebuild the entire transmission. This option typically costs less than a rebuild or a replacement.

Is it better to buy a used or rebuilt transmission?

With a transmission rebuild, or even a high-quality remanufactured transmission from a reputable company like Certified Transmission, your vehicle will retain a higher resale value than it would with a used transmission.

How do you tell if a transmission has been rebuilt?

There is almost no way to tell if the trans has been rebuilt or replaced by visually looking at it from the outside and even if it was how would it help you anyway?. There is no such thing as a life test on transmissions they are not a wear item in general.

What are the signs of a failing torque converter?

Slipping. A torque converter can slip out of gear or delay a shift its fin or bearing is damaged. …
Overheating. …
Contaminated Transmission Fluid. …
Shuddering. …
Increased Stall Speed. …
Unusual Sounds.

What included in a transmission rebuild?

Removing the transmission from your vehicle and dismantling it.
Chemically cleaning the transmission by running it through a parts washer.
Any wonky transmission parts, plus all seals and gaskets, are replaced with new ones.
Any required electrical repairs are performed.

Can I replace transmission myself?

When faced with a transmission rebuild or replacement, you can reduce the cost quite significantly by removing and replacing (R&R) the transmission yourself. Depending on the year, make and model of your vehicle and the shop labor costs in your area, you can expect to save between $550 to $1,250 or more.

What is the life expectancy of a 5.3 Vortec?

The Vortec 5.3 is widely regarded as extremely reliable, with most engines having a lifespan within the 200k-300k mileage range. I own a 2002 Suburban with the LM7 engine in it and it’s running strong at 220k miles with virtually zero engine issues over my course of ownership.

Is 4L60E reliable?

having run the gamut of transmission options out there, IMO, the stock 4l60 is just fine for 99% of trailblazer owners. if its high mileage, what are you going to do? friction material wears out. it won’t last forever.

How much horsepower can a 4L60E transmission handle?

Their Stage 2 Pro Race transmission can handle gobs of power while their Invincible Black Edition 4L60E trans can support over 1,000 ponies.

How can I tell if my 4L60E transmission is bad?

No Third Gear – You put the vehicle in drive, start off the transmission, and shift to second gear. …
No Second Gear/Reverse – The second most common symptom of a failing 4L60E transmission is your inability to shift to second gear and go reverse.

How can I make my 4L60E stronger?

Lay out the important parts on an assembly bench. …
Rebuild with an improved, thicker sun shell. …
Use five-pinion front/rear planetary. …
Use a larger clutch with an input drum reinforcement sleeve. …
Stamped Steel forward clutch apply pistons. …
Use more clutches and larger gear band servo pistons.

Which is better 4L60E or 4L80E?

Without a doubt the 4L80E is the more powerful of the two transmissions. Vehicles with powerful engines, such as big trucks for towing or high speed cars for racing, require a 4L80E rather than a 4L60E as the power of the engine is likely to break smaller, less powerful transmissions.

What's the difference between 4L80E and 4L60E?

The 4L80E is larger and heavier than the 4L60E. Its more hefty build can be tied to its 236 lbs and a length of 26.4″. Alternatively, the 4L60E weighs 150 lbs (without fluid) and it has a length of 23.5″. A comparison between the size and weight shows that the 4L80E is significantly larger and heavier.

Will a 4L60 bolt up to a 350?

The 4L60E will bolt straight up to your 350. :yes: You will need some way to control the tranny though. The OD is electronically controlled, hence the “E” at the end of the 4L60.

Is a 4L60 the same as a 700R4?

In 1990, GM decided to code and renamed their transmissions, the 700R4 is best described as a 4 speed, longitude transmission rated for vehicles around 6000 lbs. It was this information that was used to change its name to 4L60; therefore, a 700R4 and 4L60 are the same transmission.

Can a 4L60E be used without a computer?

Externally, all it needs is a 12-volt source and an engine-vacuum reference. However, if your trans is, in fact, a 4L60E, running it off a computer is mandatory. … Never mind TCC lockup; without a computer, the trans won’t shift at all.