How do you install a shower tray

Mark out the tray position.Choose the waste position.Line up side panels.Check the tray is level.Attach the waste.Apply sealant.Complete the surrounding walls.Install the side panels.

How should a shower tray be fitted?

1. Mark out the tray position.
2. Choose the waste position.
3. Line up side panels.
4. Check the tray is level.
5. Attach the waste.
6. Apply sealant.
7. Complete the surrounding walls.
8. Install the side panels.

Do you have to put cement under a shower tray?

Designed to drain water from the shower, it protects your floor from water intrusion, rot and mold. Installing one requires some skill and there are certain rules and procedures to follow when doing so. In some cases a mortar bed is a necessity; other times it isn’t.

What do you stick a shower tray down with?

Using either tile adhesive, silicone or a weak cement mix (5 parts sand/ 1 part cement) apply sufficient to board to cover entire underside of tray. Apply a minimum of 5mm thickness to lowest point of tray. More may be required in places to ensure tray is level.

What goes under shower base?

Mortar is recommended to use under all shower pans. Mortar reduces the risk of your pan slipping or cracking from an uneven surface.

Do you tile on top of a shower tray?

While some guides may recommend tiling behind the shower walls, you should indeed tile on top of the tray. … The bottom rows of tiles should be put in place carefully, one at a time, starting from the trim and cutting into the corner space.

Do I tile floor before fitting shower tray?

We always advise fitting the shower tray before tiling the walls or installing wall panels as this ensures a more watertight seal around the sides of the tray.

How thick should mortar be for shower tray?

The minimum thickness of mortar at the lowest point should be 5mm after the tray has been levelled. Check that the top of the tray is level (Fig 4). Ensure that the entire base of the tray is fully supported as the base of the tray may not be entirely level. This is due to the manufacturing process.

Do you waterproof under a shower base?

DON’T ignore the importance of waterproofing when installing an acrylic shower base. The walls and the area around the top of the acrylic base along the wall are very important for proper waterproofing and it is essential that it be done correctly. … In a bathroom, proper waterproofing is non-negotiable.

Can you use sand under a shower pan?

Dump enough dry pack Sand Mix into the shower base to form a level perimeter around the entire shower pan at your high point mark. Pack the perimeter layer with a rubber or wooden float by repeatedly tamping the material down. Use a hand level to maintain level around the perimeter. … Pack down material as you progress.

Article first time published on

Who installs shower pans?

Plumbers generally install the shower liner, new drain trap and strainer. In the old days, when lead and copper were used, you wouldn’t expect the tile person to install the pan…

What do you put under shower pan for support?

Line the underside of the shower drain flange’s rim with latex/acrylic or silicone caulk, per manufacturer’s instructions. In some cases, plumber’s putty – a commonly used drain flange sealant – will degrade the shower pan material, so be sure to check the manufacturer’s instructions carefully here.

Do you tile under a shower base?

You dont want tile underneath as it may or may not end up level, it may or may not come loose after weight is put onto it, and most importantly grout is not waterproof…it will absorb water and you definitely dont want that under the shower.

Do you put toilet first or tile?

The bathroom fitters are unanimous—if you’re looking for a high quality finish, with a better seal against water damage, then always tile the floor first.

Does shower pan liner go behind backer board?

The wallboard must be installed 1/8 inch above the shower pan. If the shower pan is not in place, the wallboard height must be guessed, which can lead to inaccuracies and an expansion gap that is too large or too small.

How do you install a shower pan on a concrete floor?

1. Remove enough concrete to allow space for the waste pipe.
2. Place pipe and drainage tool into the hole.
3. Test the pan to make sure it fits properly.
4. Apply mortar to the concrete base.
5. Place the shower tray over the mortar, pressing firmly.
6. Screw the drain into place.
7. Let the mortar dry for 24 hours.

Do I need to waterproof shower walls before tiling?

Applying a waterproofing sealer to cement backer board before tiling. Since a tile tub or shower surround gets wet, it requires a waterproof backing, rather than just drywall.

How many bags of sand do I put in a shower pan?

I usually mix one bag sand/topping mix with a half bag of sand (25lbs) to make things easy and have had good luck with that. Be very careful with how much water you add to the deck mud as you mix it up. It’s referred to as dry-pack mortar for a reason. Do not add water like you are mixing concrete.

What kind of concrete do you use for a shower pan?

The best concrete mix for shower pans is made by Quikrete. They make two products, the first is called Floor Mud, the 2nd is their Sand/Topping mix. Both work great for building a shower pan.

Which mortar for shower walls?

Because thinset is not affected by moisture, it is best for floor tile and any tile in wet areas, including shower floors, walls, and ceilings and tub surrounds. Since thinset tile mortar may crack, you may wish to mix it with a special latex additive to increase its strength.

How thick should a shower pan be?

The shower pan base mortar layer thickness should be approximately ½ to 1 inch thick. Since the shower floor already has a pre-slope, just apply a base mortar layer that has an even thickness throughout the shower floor area.

How much slope should a shower pan have?

To efficiently drain, the recommended minimum slope for a shower floor is about 4 percent, or a 1/2 inch drop per every 12 inches from the shower walls to the drain. In traditional tile shower construction, this slope is established in the mortar pre-pan.

Can you use concrete for shower floor?

Concrete is perfectly adequate, if not recommended, for use as the shower pan base for materials such as stone, tile or mosaic tile to be used as the finish surface (as long as there is a proper membrane between the concrete and any vulnerable surrounding material).

How much does it cost to put in a shower pan?

According to Porch.com, the average cost to install a shower pan is about $1,550 for both labor and materials. Typical costs can range from about $1,000 to $2,000, depending on where you live and the type of shower pan you choose.

How much does a mud set shower pan cost?

National average cost$1,600Minimum cost$300Maximum cost$4,600Average range$900 to $2,300

Is a shower pan considered plumbing?

In fact, shower pan losses in general are a common occurrence and are related to a plumbing issue, i.e., a shower pan failure. Most likely the insurance company will not pay for the actual shower pan itself, but will pay for the tear out and replacement of building items to get to the shower pan.

How do I stop my shower pan from flexing?

Contractors typically use a material called bedded mortar to cover the area of subfloor where a shower base will sit. This material resembles concrete and, once set, hardens and prevents the tub from flexing.

How do I stop my shower tray from flexing?

In severe cases—especially if the flexing has caused the shower pan itself to crack—the only solution is to remove the base to make the necessary repairs. This can involve better shimming for the support ribs beneath the pan or laying a mortar bed to support the pan over its entire surface.