How do I reset my Fisher and Paykel dishwasher E6

Fisher and Paykel Dishwasher Dishdrawer Error Code E6 = The first 4 program indicator lights are flashing. Error Code Cause: Flood switch activated. How To Fix: Turn the water and power off to the dishwasher and back on to try and reset. Check Flood Switch.

How do you run a diagnostic on a Fisher Paykel dishwasher?

Diagnostic Mode. With Power off, press/hold Keylock, then press Start/Pause at the same time for 5 seconds. Release the buttons when it powers-on. Press Power once.

Why is my Fisher and Paykel DishDrawer beeping?

The drainage hose may be blocked or kinked, or the connection to drainage pipe may be blocked. Ensure the drainage hose and connection to pipes are not blocked. once to stop the beeping, and then again to clear the fault. to resume the wash program.

Why is my Fisher and Paykel dishwasher not turning on?

Ensure the dishwasher is plugged in and the power supply is turned on at the wall. Ensure the door is firmly closed. Ensure water is connected and turned on. Check the strainer and clean if necessary, it is located where the water inlet hose screws into the tap.

What does E6 mean on a dishwasher?

An E6 error code of the Bosch dishwasher means that there are problems with the sensor that controls the water turbidity. It is also called the Aqua Sensor. In the dishwasher, this sensor detects the turbidity of the water due to the presence of small particles of dirt, food residues and other things inside it.

Where is model number on Fisher Paykel dishwasher?

Located on the left hand side of the appliance, underneath the top drawer and hidden when closed.

What does U6 mean on a Fisher & Paykel dishwasher?

U6. The spray arm has loosened or come off its mounting, or water pressure is too low.

How do you replace the Fisher Paykel control board?

Push in on the tab on each side of the control board and remove the control board. There is one tab on each side of the control board. Line the new control board up and secure it to the tabs by pushing it into place until the tabs lock. Plug the wire harness into the new control board.

How do I fix the f1 on my dishwasher?

Locate the drain-access filter panel on the bottom of the drawer.
Remove the rack that sits above it.
Pull up to lift the drain filter and remove it from the machine.
Set the filter under the faucet to rinse it clean with cold water.
Reinstall the filter and confirm that it sits flush with the bottom of the DishDrawer.

How do I reset my Fisher and Paykel dishwasher?

Press the power button to turn off power to the Fisher & Paykel dishwasher.
Wait a few minutes and then press the power button to restore power.
Turn off and unplug the dishwasher if the issue remains.
Wait five minutes and restore power to the unit.

Article first time published on

How do I turn on Fisher and Paykel DishDrawer?

To activate, press and hold until you hear two beeps (5 seconds). The light above the button will glow steadily. To cancel, press and hold until the light above it goes out. Keep this document handy for easy reference.

Why isn't my dishwasher heating up?

If you have your dishwasher connected to the cold water supply then it’s highly likely that a faulty heating element or thermostat are the cause of the water not heating. If you’re connecting to hot then it’s worth checking the water supply to check that there is actually an issue with the dishwasher and not elsewhere.

How do I get my Fisher and Paykel dishwasher to stop beeping?

Solution # 1: Switch it ON and OFF Sometimes, the beeping error on Fisher and Paykel DishDrawer Dishwasher is just abnormal, and may be fixed by simply resetting it. To do so, turn it OFF and after 10-15 minutes, turn it ON it.

What model DishDrawer do I have?

DishDrawer™ Located on the left hand side of the appliance, underneath the top drawer and hidden when closed.

How do I cancel my cycle Fisher and Paykel dishwasher?

To cancel, press and hold until the light above it goes out. Press to cancel a wash that has already started or to cancel the Delay start setting. If there is any water in the drawer,it will automatically drain before the dishwasher turns off.

What does E9 mean on Fisher and Paykel dishwasher?

Fault CodePossible Cause of FaultE6Fault with the drying fan.E7Electronics fault—detergent dispensing system.E8Electronics fault—other systems.E9Electronics fault—controller.

What does F4 mean on a Fisher and Paykel dishwasher?

F4. Heating Element Failed. You will require a Service Technician to assist –

What does A1 mean on Fisher Paykel dishwasher?

Check for a kinked drain hose, blocked waste connection, highloop not properly installed, drain hose not routed correctly or spray arms not in place. No water supply. ( This is displayed as an A1 fault) Check water is connected and turned on. The dishwasher is beeping continuously.

What does E2 mean on a Fisher and Paykel dishwasher?

Fisher and Paykel Dishwasher Dishdrawer Error Code E2 = 1 and 3 program indicator lights are flashing. Error Code Cause: Temperature sensor is faulty. How To Fix: Turn the water and power off to the dishwasher and back on to try and reset.

What does FCO mean on dishwasher?

Error CodesProblemFCOMotor fault. Switch dishwasher OFF at the power supply. Wait a few moments and switch ON again. If the fault persists, turn water off and disconnect from the power supply. Call Customer Care.

What does E5 mean on a dishwasher?

Fisher and Paykel Dishwasher Dishdrawer Error Code E5 is the first three program indicator lights flashing. There is a water supply hose that is bent or crimped. The drain hose is not high.

Where is Fisher Paykel serial number?

Serial label located on the back of the top panel. Depending on Model, either: Serial label located at the top of the door frame when the door is opened. or Serial label located on the back of the chassis. Serial label located on the inside of the door or on the back of the product.

Where is the model number on dishwasher?

Usually dishwasher model numbers are displayed behind the door. Check the top edge of the door inside, and all of the sides. Next, see the base of the dishwasher or the “kick strip” under the door at the front.

How do you turn on a Fisher and Paykel oven?

Open the oven door to its full extent. …
Press the oven control knob right down (the igniters will start ‘clicking’), turn the knob counter-clockwise (fig. …
Check the oven burner has lit; if not, turn the knob clockwise back to “OFF” and repeat the procedure from step 2.

What does F1 error mean?

F1 Error. The F1 error means that there is an electronics failure within the oven. This failure can occur within the keypad itself, the electronic oven control or the oven temperature sensor. … The error can also indicate data corruption within the oven’s electronic controller.

What does F mean on a dishwasher?

Flood switch activated. Turn the dishwasher OFF and ON again. If fault persists, turn water off and disconnect the dishwasher from the power supply.

How do you remove the front panel on a Fisher and Paykel dishwasher?

Grasp the center bar of the pin with the pliers and pull it straight out. Repeat for the pin on the other side of the drawer. Pull the front of the drawer down to free it from the handle top tabs. Slide the grounding wire off of the panel and then remove.

How do I replace my dishwasher control board?

Shut off electrical power. Unplug the dishwasher or shut off the house circuit breaker for the dishwasher. …
Remove the outer door panel and control panel. …
Remove the electronic control board. …
Install the new electronic control board. …
Reinstall the outer door panel and control panel. …
Restore electrical power.

How do I reset my Fisher and Paykel washing machine?

Turn the dial to select ‘Spin’.
Touch and hold the ‘Delay Start’ ‘More’ , the ‘Delay Start’ ‘Less’ and ‘Options’ buttons together for 3 seconds will appear on the screen and the machine will beep.
Your washer will now be reset to the default settings.

What does F2 mean on dishwasher?

If your dishwasher doesn’t drain properly, you’ll see standing water on the bottom of the dishwasher when the cycle is complete and the error code F2 may be displayed, according to the Westinghouse dishwasher user manual.